AMD64 Overclocking Guide - Page 3

deathvirus_me · 08-07-2006, 01:51 AM

Thats a pretty low increase .. i've got a 100 points increase in 3DMark06 ..., so u can pretty much get the idea ... Whats the 3DMark03 CPU Score btw ??

Also ,, with the increased HT and higehr clocked mem (which means a pretty higher mem. bandwidth) .. u should get much better CPU scores ....

**bakuryu** · 08-07-2006, 01:58 AM

Cpu score was 1025. Previously it was around 910

**bakuryu** · 09-07-2006, 10:00 PM

Amazing I had no idea my memory could tolerate a HTL speed of 1178MHZ !! Simply amazed !!

Well windows was stable, but nTune was already showing me in the RED zone for both memory and HTL. Forced memory to 333MHz, and that rose too 390MHz. QS rating of 4082+

If only I had a better memory stick like corsair that I could depend upon.

deathvirus_me · 10-07-2006, 02:45 AM

Stupid fool .. why don't u decrease the HT multiplier to 4x , then the HTT should be at ~940 MHz , which is quite safe ... try it ...

**bakuryu** · 10-07-2006, 11:30 PM

I think the clock speed is still a bit high. Well anyways, I don't need to overclock right now to play NFS MW, and surf the net ...LOL ... but maybe some time later, I may overclock, when a higher speed is required.

**bakuryu** · 16-08-2006, 01:02 PM

Well, as to some doubts expressed wether with changed RAM timings, my system would boot or not, just tried it and well ... success

Sam RuleZ · 16-08-2006, 09:20 PM

Hey cooll....bakuryu.....oc'ed ram haaan?? Running at 440MHz ??Stable naa??Zion on which chips??

**bakuryu** · 16-08-2006, 09:26 PM

Yes it was stable ... but I was afraid 1100 MHz HTL speed (max 1050 is recommended) .. and these Zion .... have no faith in them. Well I don't need an OC right now. So just down clocked again. If I need to OC, then I got to redice the multiplier to 4X, CPu multiplier to 10 and then maybe OC my FSB to 240 ... like what deathvirus did.

With an HTL speed of 1100 my machine was literally flying

...... sadly had in been corsair ... I would have had some faith. But with Zion .... absolutely no faith with OC

Sam RuleZ · 16-08-2006, 09:36 PM

Quote:

Yes it was stable ... but I was afraid 1100 MHz HTL speed

Was it stable idle or @ Prime95 or Super Pi?

Which chips is the memory based on???

Quote:

sadly had in been corsair

Yaa....it would have been corsair,OCZ,UCCC,D43 then no need to even overclock the memory!!!

just start increasing the FSB...lol...

**bakuryu** · 16-08-2006, 10:11 PM

Well .. frankly speaking I am 90% sure my system will be unstable in Prime95 torture tests ... 1100Mhz .. can even damage my memory. So I never risked running a stress test at that speed.

But Super PI 1M test completed successfully. Took 4 seconds less. Completed in 37 seconds, while normally at stick Super PI 1M takes 41secs to complete. And the major adv. of a superior memory would be that I could get 1T latency. Currently it is 2T ... 1T system highly unstable

Quote:

Which chips is the memory based on???

Didn't understand. My memory is a Zion DDR400 running dual channel, 1Gb each.

08-07-2006, 01:51 AM	#21
deathvirus_me Senior Member (500+) Join Date: May 2006 Location: Bhatpara , India Age: 22 Posts: 830 Thanks: 1 Thanked 28 Times in 24 Posts Rep Power: 18	Thats a pretty low increase .. i've got a 100 points increase in 3DMark06 ..., so u can pretty much get the idea ... Whats the 3DMark03 CPU Score btw ?? Also ,, with the increased HT and higehr clocked mem (which means a pretty higher mem. bandwidth) .. u should get much better CPU scores .... __________________

08-07-2006, 01:58 AM	#22
bakuryu ƒ(ψ)=Θº×φ Join Date: May 2006 Location: India Age: 22 Posts: 5,032 Thanks: 12 Thanked 392 Times in 362 Posts Rep Power: 69	Cpu score was 1025. Previously it was around 910 __________________ Please don't click here

16-08-2006, 09:20 PM	#27
Sam RuleZ Senior Member (500+) Join Date: Jun 2006 Location: Mumbai. Age: 16 Posts: 505 Thanks: 6 Thanked 27 Times in 22 Posts Rep Power: 17	Hey cooll....bakuryu.....oc'ed ram haaan?? Running at 440MHz ??Stable naa??Zion on which chips?? __________________ "Its better to get burnt, than to fade away"-Kurt Cobain.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Beginers guide to Overclocking	Xtra	TIPS 'n' TRICKS	7	14-03-2008 01:18 AM
Does Overclocking YOur CPU cause problems with your activation?	Alfred Kaufmann	Windows Vista All	9	01-09-2007 03:30 AM
Help needed - Overclocking my PC	Night_virus	Hardware Troubleshooting	10	27-06-2007 07:48 PM
Overclocking nvidia cards.	Sam RuleZ	Guides	8	15-01-2007 02:06 PM
Overclocking ur CPU	deathvirus_me	Processors & Motherboards	19	31-05-2006 10:35 PM

09-07-2006, 10:00 PM	#23
bakuryu ƒ(ψ)=Θº×φ Join Date: May 2006 Location: India Age: 22 Posts: 5,032 Thanks: 12 Thanked 392 Times in 362 Posts Rep Power: 69	Amazing I had no idea my memory could tolerate a HTL speed of 1178MHZ !! Simply amazed !! Well windows was stable, but nTune was already showing me in the RED zone for both memory and HTL. Forced memory to 333MHz, and that rose too 390MHz. QS rating of 4082+ If only I had a better memory stick like corsair that I could depend upon.

10-07-2006, 02:45 AM	#24
deathvirus_me Senior Member (500+) Join Date: May 2006 Location: Bhatpara , India Age: 22 Posts: 830 Thanks: 1 Thanked 28 Times in 24 Posts Rep Power: 18	Stupid fool .. why don't u decrease the HT multiplier to 4x , then the HTT should be at ~940 MHz , which is quite safe ... try it ...

10-07-2006, 11:30 PM	#25
bakuryu ƒ(ψ)=Θº×φ Join Date: May 2006 Location: India Age: 22 Posts: 5,032 Thanks: 12 Thanked 392 Times in 362 Posts Rep Power: 69	I think the clock speed is still a bit high. Well anyways, I don't need to overclock right now to play NFS MW, and surf the net ...LOL ... but maybe some time later, I may overclock, when a higher speed is required.

16-08-2006, 01:02 PM	#26
bakuryu ƒ(ψ)=Θº×φ Join Date: May 2006 Location: India Age: 22 Posts: 5,032 Thanks: 12 Thanked 392 Times in 362 Posts Rep Power: 69	Well, as to some doubts expressed wether with changed RAM timings, my system would boot or not, just tried it and well ... success

16-08-2006, 09:26 PM	#28
bakuryu ƒ(ψ)=Θº×φ Join Date: May 2006 Location: India Age: 22 Posts: 5,032 Thanks: 12 Thanked 392 Times in 362 Posts Rep Power: 69	Yes it was stable ... but I was afraid 1100 MHz HTL speed (max 1050 is recommended) .. and these Zion .... have no faith in them. Well I don't need an OC right now. So just down clocked again. If I need to OC, then I got to redice the multiplier to 4X, CPu multiplier to 10 and then maybe OC my FSB to 240 ... like what deathvirus did. With an HTL speed of 1100 my machine was literally flying ...... sadly had in been corsair ... I would have had some faith. But with Zion .... absolutely no faith with OC